收藏本站
CAT25128
Byte Write
Once the WEL bit is set, the user may execute a write
sequence, by sending a WRITE instruction, a 16 ? bit address
and data as shown in Figure 5. Only 14 significant address
bits are used by the CAT25128. The rest are don’t care bits,
as shown in Table 14. Internal programming will start after
the low to high CS transition. During an internal write cycle,
all commands, except for RDSR (Read Status Register) will
be ignored. The RDY bit will indicate if the internal write
cycle is in progress (RDY high), or the device is ready to
accept commands (RDY low).
Page Write
After sending the first data byte to the CAT25128, the host
may continue sending data, up to a total of 64 bytes,
according to timing shown in Figure 6. After each data byte,
the lower order address bits are automatically incremented,
while the higher order address bits (page address) remain
unchanged. If during this process the end of page is
exceeded, then loading will “roll over” to the first byte in the
page, thus possibly overwriting previously loaded data.
Table 14. BYTE ADDRESS
Following completion of the write cycle, the CAT25128 is
automatically returned to the write disable state.
Write Identification Page
The additional 64 ? byte Identification Page (IP) can be
written with user data using the same Write commands
sequence as used for Page Write to the main memory array
(Figure 6). The IPL bit from the Status Register must be set
(IPL = 1) using the WRSR instruction, before attempting
to write to the IP.
The address bits [A15:A6] are Don’t Care and the
[A5:A0] bits define the byte address within the
Identification Page. In addition, the Byte Address must point
to a location outside the protected area defined by the BP1,
BP0 bits from the Status Register. When the full memory
array is write protected (BP1, BP0 = 1,1), the write
instruction to the IP is not accepted and not executed.
Also, the write to the IP is not accepted if the LIP bit from
the Status Register is set to 1 (the page is locked in
Read ? only mode).
Address Significant Bits
Address Don’t Care Bits
# Address Clock Pulses
Main Memory Array
Identification Page*
A13 ? A0
A5 ? A0
A15 ? A14
A15 ? A6
16
16
*New Product only.
CS
0
1
2
3
4
5
6
7
8
21
22 23
24
25
26 27
28
29
30 31
SCK
OPCODE
BYTE ADDRESS*
DATA IN
SI
0
0
0
0
0
0
1
0
A N
A 0 D7 D6 D5 D4 D3 D2 D1 D0
SO
HIGH IMPEDANCE
Dashed Line = mode (1, 1)
* Please check the Byte Address Table (Table 14)
Figure 5. Byte WRITE Timing
CS
0
1
2
3
4
5
6
7
8
21
22
23 24 ? 31 3 2 ? 39 24+(N ? 1)x8 ? 1 .. 24+(N ? 1)x8
SCK
24+Nx8 ? 1
OPCODE
BYTE ADDRESS*
DATA IN
Data Byte N
SI
0
0
0
0
0
0
1
0
A N
A 0
Data Data Data
Byte 1 Byte 2 Byte 3
7..1
0
SO
Dashed Line = mode (1, 1)
HIGH IMPEDANCE
* Please check the Byte Address Table (Table 14)
Figure 6. Page WRITE Timing
http://onsemi.com
9
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
CAT25160HU4I-GT3 IC EEPROM SRL 16KB I2C 8UDFN
CAT25256XI-T2 IC EEPROM 256KBIT 10MHZ 8SOIC
CAT25320LI-G IC EEPROM 32KBIT 10MHZ 8DIP
CAT25512HU5I-GT3 IC EEPROM SRL 512KB I2C 8UDFN
CAT25640HU4I-GT3 IC EEPROM SRL 64KB I2C 8UDFN
CAT25640LI-G IC EEPROM 64KBIT 10MHZ 8DIP
CAT28C16AXI-90T IC EEPROM 16KB PARALLEL 24SOIC
CAT28C256G-15T IC EEPROM 256KB PARALLEL 32PLCC
相关代理商/技术参数
CAT25128XI-T2 功能描述:电可擦除可编程只读存储器 128K SPI Serial RoHS:否 制造商:Atmel 存储容量:2 Kbit 组织:256 B x 8 数据保留:100 yr 最大时钟频率:1000 KHz 最大工作电流:6 uA 工作电源电压:1.7 V to 5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8
CAT25128YE-GT3 制造商:ON Semiconductor 功能描述:
CAT25128YI-G 功能描述:电可擦除可编程只读存储器 128K (16Kx8) SPI 1.8 to 5.5V RoHS:否 制造商:Atmel 存储容量:2 Kbit 组织:256 B x 8 数据保留:100 yr 最大时钟频率:1000 KHz 最大工作电流:6 uA 工作电源电压:1.7 V to 5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8
CAT25128YI-GT3 功能描述:电可擦除可编程只读存储器 128K SPI Serial CMOS 电可擦除可编程只读存储器 RoHS:否 制造商:Atmel 存储容量:2 Kbit 组织:256 B x 8 数据保留:100 yr 最大时钟频率:1000 KHz 最大工作电流:6 uA 工作电源电压:1.7 V to 5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8
CAT25-130JA 功能描述:电阻器网络与阵列 13ohm 5% Concave 8resistors RoHS:否 制造商:Vishay/Thin Film 产品类型:Networks 电路类型:Divider 电阻器数量: 电阻数值:10 kOhms 容差:0.1 % 温度系数: 管脚数量:3 工作温度范围:- 55 C to + 155 C 尺寸:1.02 mm W x 3.05 mm L x 1.4 mm H 引线间隔: 端接类型:SMD/SMT 封装:Reel
CAT25-130JALF 功能描述:电阻器网络与阵列 13ohm 5% Concave 8resistors RoHS:否 制造商:Vishay/Thin Film 产品类型:Networks 电路类型:Divider 电阻器数量: 电阻数值:10 kOhms 容差:0.1 % 温度系数: 管脚数量:3 工作温度范围:- 55 C to + 155 C 尺寸:1.02 mm W x 3.05 mm L x 1.4 mm H 引线间隔: 端接类型:SMD/SMT 封装:Reel
CAT25-131JA 功能描述:电阻器网络与阵列 130ohm 5% Concave 8resistors RoHS:否 制造商:Vishay/Thin Film 产品类型:Networks 电路类型:Divider 电阻器数量: 电阻数值:10 kOhms 容差:0.1 % 温度系数: 管脚数量:3 工作温度范围:- 55 C to + 155 C 尺寸:1.02 mm W x 3.05 mm L x 1.4 mm H 引线间隔: 端接类型:SMD/SMT 封装:Reel
CAT25-131JALF 功能描述:电阻器网络与阵列 130ohm 5% Concave 8resistors RoHS:否 制造商:Vishay/Thin Film 产品类型:Networks 电路类型:Divider 电阻器数量: 电阻数值:10 kOhms 容差:0.1 % 温度系数: 管脚数量:3 工作温度范围:- 55 C to + 155 C 尺寸:1.02 mm W x 3.05 mm L x 1.4 mm H 引线间隔: 端接类型:SMD/SMT 封装:Reel